+- JapCarForum (https://www.japcarforum.com)
+-- Forum: Cars, Cars, Cars! (https://www.japcarforum.com/forumdisplay.php?fid=11)
+--- Forum: Project Cars (https://www.japcarforum.com/forumdisplay.php?fid=156)
+--- Thread: Bandit's Supercharged IS200 take 2 :-) (/showthread.php?tid=5114)
Bandit's Supercharged IS200 take 2 :-) - Bandit - 24-06-2018
Cheers guys :thumbup1:
@Chri5, no mate i have a big polishing machine that i use,
I just sand off the paint/rust etc, and run them under the polisher with a couple of different pastes :thumbup1:
Bandit's Supercharged IS200 take 2 :-) - Lexuspat - 25-06-2018
bandit that looks mint
when shall i bring mine round for you to do lol
Bandit's Supercharged IS200 take 2 :-) - Bandit - 25-06-2018
Cheers matey :thumbup1: got loads to do yet
just making some models for the stainless PAS bottle covers 
Bandit's Supercharged IS200 take 2 :-) - Lexuspat - 25-06-2018
i would love a set of covers for all the lids under there just wouldnt know where to start
Bandit's Supercharged IS200 take 2 :-) - garyskisplym - 26-06-2018
looks good
you love your shiny dont you
Bandit's Supercharged IS200 take 2 :-) - Bandit - 27-06-2018
Lexuspat i would love a set of covers for all the lids under there just wouldnt know where to start
Not too hard to do mate, just need to make some cardboard models first?
This is the rough model i made first for the power steering bottle cover?
![[Image: pascovercard1.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/My%20Lexus%20Supercharged%20Lexus%20IS200/pascovercard1.jpg)
Then made it out of metal, and brazed the top on with silver solder...
![[Image: pascovermetal1.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/My%20Lexus%20Supercharged%20Lexus%20IS200/pascovermetal1.jpg)
Still got to tidy it up, trim the edges and cut the centre hole out etc..
Both models together...
![[Image: pasbothmodels1.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/My%20Lexus%20Supercharged%20Lexus%20IS200/pasbothmodels1.jpg)
After i cut the centre out i'll see how it fits and adjust if needed,
then when the polished metal i've ordered comes i'll redo it, and hopefully it'll be a bit tidier :thumbup1:
.
Bandit's Supercharged IS200 take 2 :-) - Dark Samurai - 27-06-2018
Looking good matey, cannot wait to see this at JAE or earlier!
Group buy on these now I reckon?
How do they fit, adhesive of tight fitting so nothing needed?
Bandit's Supercharged IS200 take 2 :-) - Bandit - 27-06-2018
They just slide over the top of the bottle mate, then you put the top back on and it holds them in place, so very simple to fit :thumbup1:
Bandit's Supercharged IS200 take 2 :-) - Dark Samurai - 27-06-2018
so big enough to fit over the hole, but not big enough to fit over the cap, clever!!
Bandit's Supercharged IS200 take 2 :-) - Bandit - 27-06-2018
Yeh very simple mate :thumbup:
There's a pic of the old one i made in the garage section