+- JapCarForum (https://www.japcarforum.com)
+-- Forum: Cars, Cars, Cars! (https://www.japcarforum.com/forumdisplay.php?fid=11)
+--- Forum: General Car Maintenance (https://www.japcarforum.com/forumdisplay.php?fid=150)
+--- Thread: Carbon fiber Wrapping parts of the Stagea (/showthread.php?tid=7463)
Carbon fiber Wrapping parts of the Stagea - spikes - 04-04-2019
agree with stav that fairing looks well cool :thumbup1:
Carbon fiber Wrapping parts of the Stagea - mplavery - 04-04-2019
Looks great mate !
I did have a go at my rad shroud but i could not get a nice finish, I then thought if it gets hot from the engine it would come off again lol
Might have another go at some interior bits again
How about the door handle surrounds Rabs ?
Carbon fiber Wrapping parts of the Stagea - jimxms - 05-04-2019
If you wanna try the di-noc stuff mate I've got some bits left over that you could use? They wont cover anything significant, but it'll give you an idea of what its like to work with before shelling out ~£50 for what you'd need to do your dash.
Carbon fiber Wrapping parts of the Stagea - Phil01 - 05-04-2019
Jim have you got a length of approximately 1m long and say 300mm wide to cover a small piece of my front lower spoiler.
Sent from my GT-I9000 using Tapatalk
Carbon fiber Wrapping parts of the Stagea - jimxms - 05-04-2019
I'll have a lookie for ya when I get home tonight mate.
Carbon fiber Wrapping parts of the Stagea - Rabster - 05-04-2019
ok so today i had some Carbon fibre Wrap arrive so i got started by removing the 1st 2 biits
![[Image: c17e17e0.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/c17e17e0.jpg)
![[Image: 104df657.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/104df657.jpg)
i then cut a sheets oversized for what i needed
![[Image: 689a5a52.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/689a5a52.jpg)
![[Image: b5e4c5ca.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/b5e4c5ca.jpg)
then i wrapped not many pictures from this bit im sorry
but the finished parts
![[Image: 8e148520.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/8e148520.jpg)
![[Image: 1defc128.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/1defc128.jpg)
![[Image: 40908714.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/40908714.jpg)
![[Image: 83d89eb9.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/83d89eb9.jpg)
![[Image: 9faf18ff.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/9faf18ff.jpg)
![[Image: 5b77afb5.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/carbon%20wrapping/5b77afb5.jpg)
im not to happy with the air ducts so i may redo them but i had fun lol
what are your verdicts
Before pic
![[Image: f6c1424f.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Stagea/f6c1424f.jpg)
After Pic
Carbon fiber Wrapping parts of the Stagea - Phil01 - 05-04-2019
they look spot on andy,
whats the issue with the vent?
Carbon fiber Wrapping parts of the Stagea - jimxms - 05-04-2019
Looking good mate. How hard did you find it to get the di-noc to stick to the recessed area of the air vents?
Carbon fiber Wrapping parts of the Stagea - jasons - 05-04-2019
Like it!- well done.
J
Carbon fiber Wrapping parts of the Stagea - Rabster - 05-04-2019
it was easy enough to get it to stretch into the vent area but the fact its got the support in the middle meant that it got pulled about 2 much and over stretched so broke and i had to fit another piece over the top i have tried to match the weave but im not happy with it,
you all know how fussy i am about my parts lol