+- JapCarForum (https://www.japcarforum.com)
+-- Forum: Cars, Cars, Cars! (https://www.japcarforum.com/forumdisplay.php?fid=11)
+--- Forum: Project Cars (https://www.japcarforum.com/forumdisplay.php?fid=156)
+--- Thread: My little project - IS200 Turbo (/showthread.php?tid=1216)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
My little project - IS200 Turbo - parthiban - 18-01-2018
Good stuff, few sleepless nights ahead then! :w00t:
My little project - IS200 Turbo - Lexusboy - 19-01-2018
Not long now mate, i guess you may have enough time to finish your other project:wink:
My little project - IS200 Turbo - steviewevie - 19-01-2018
russelllinn How come noble need the car for so long?
Sorry, forgot to answer this bit. Actually, I don't know, but apparently this is their standard sort of time they have a car for, for mapping.
Since it's had different internals put in it, they'll be gentle at first with it, before doing the proper power runs.
Noble will install the uprated (550cc) injectors too.
My little project - IS200 Turbo - FirebirdPhil - 19-01-2018
Also you need to map a car at all points of the heat cycles, drive it on the road etc. You can't map a cold start if the engine isn't absolutely cold.
Mine had a couple of flat spots that didn't show on the RR but when driven on a real road they were smoothed out.
This all takes time, I have a feeling SPC quote 2 days for mapping and getting it 100% right 1st time.
My little project - IS200 Turbo - steviewevie - 19-01-2018
The new turbo flang(e) is being finished off this afternoon (don't ask me why it wasn't yesterday afternoon), and is being picked up by Charlesworth first thing tomorrow mornight, so it can be fitted.
My little project - IS200 Turbo - steviewevie - 20-01-2018
Charlesworth have the new turbo flang(e) and are fitting it tonight. Should be getting it over to Noble tomorrow.
Right now the engine has some "running in" oil in it. When it comes back from Noble, it'll have an oil/filter change.
My little project - IS200 Turbo - parthiban - 20-01-2018
Once it's off to Noble it's pretty much ready to go then is it? Definitely getting close then :biggrin:
steviewevie and is being picked up by Charlesworth first thing tomorrow mornight
Mornight? What time of day is that? :laugh:
My little project - IS200 Turbo - FirebirdPhil - 20-01-2018
Sounds like Greek time that - some time in the Morning or it could be tonight!!!
My little project - IS200 Turbo - dimis - 20-01-2018
You are almost near the finish line mate. :thumbup1:
My little project - IS200 Turbo - steviewevie - 20-01-2018
parthiban Once it's off to Noble it's pretty much ready to go then is it? Definitely getting close then :biggrin:Yep, all it really needs after Noble is an oil/filter change, and a bit of a polish ! :biggrin:
Quote:Mornight? What time of day is that? :laugh:
:laugh: Don't know what on earth I was thinking of there ! :laugh: