how to tell if a TTE/TRD kit is genuine?
how to tell if a TTE/TRD kit is genuine?
![[Image: ormiedit1-2.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/ormiedit1-2.jpg)
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
the two smaller ones are for the rear and the two larger ones on the left are what you need
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
![[Image: DSC01379.jpg]](http://i206.photobucket.com/albums/bb160/foodie69jason/DSC01379.jpg)
you need 3m tape though....the good stuff
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
you cant get a fitting kit........you dont need one plenty of us have fitted the skirts with out them...but you do need the parts above.......
you need 3m tape though....the good stuff
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
You should have a plastic trim screwed into the back of the front arches like this.
![[Image: P1010479.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010479.jpg)
You just need to remove the 2 bottom screws. These hold the front end of the side skirt when fitted.
and a small plastic trim in the rear arch....
![[Image: P1010480.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010480.jpg)
There are 2 holes in the rear end of the side skirt but you only use the bottom one.
Ormi has made a little bracket to fit in top one but don't worry don't have to fit it, it just holds the skirt a bit closer.
I used double sided tape along the top edge on mine like this.
![[Image: P1010494.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010494.jpg)
![[Image: P1010495.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010495.jpg)
![[Image: P1010496.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010496.jpg)
I also stuck some tape along the bottom to stick it to the underside of the sill.
Stick the tape to the skirt leaving the red top tape on until you have it on the car. I stuck the tape to the skirts and left over night to stick good. I also used a little wallpaper seam roller to get the tape well stuck to the skirt.
Pull a bit of the red top tape off.
Offer it up to the car and put the screws back in the front (2 off) and rear (1 off)
![[Image: P1010498.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010498.jpg)
Then pull the protective red tape away and push to stick to the car as you go.
![[Image: P1010500.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010500.jpg)
![[Image: P1010499.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010499.jpg)
Job finished.
![[Image: P1010504.jpg]](http://i779.photobucket.com/albums/yy75/dave_dixon/Daves%20Lexus/P1010504.jpg)
Hope that helps.
Dave
I fitted my side skirts without the fitting kit just a few weeks ago and took loads of pictures. Here's just a few to try and help you get your's done.
You should have a plastic trim screwed into the back of the front arches like this.
You just need to remove the 2 bottom screws. These hold the front end of the side skirt when fitted.
and a small plastic trim in the rear arch....
There are 2 holes in the rear end of the side skirt but you only use the bottom one.
Ormi has made a little bracket to fit in top one but don't worry don't have to fit it, it just holds the skirt a bit closer.
I used double sided tape along the top edge on mine like this.
I also stuck some tape along the bottom to stick it to the underside of the sill.
Stick the tape to the skirt leaving the red top tape on until you have it on the car. I stuck the tape to the skirts and left over night to stick good. I also used a little wallpaper seam roller to get the tape well stuck to the skirt.
Pull a bit of the red top tape off.
Offer it up to the car and put the screws back in the front (2 off) and rear (1 off)
Then pull the protective red tape away and push to stick to the car as you go.
Job finished.
Hope that helps.
Dave
dodgydave I fitted my side skirts without the fitting kit just a few weeks ago and took loads of pictures. Here's just a few to try and help you get your's done.
You should have a plastic trim screwed into the back of the front arches like this.
Hope that helps.
Dave
dave, thanks but its this plastic trim that im missing and i thought was a fitting kit!
dodgydave I fitted my side skirts without the fitting kit just a few weeks ago and took loads of pictures. Here's just a few to try and help you get your's done.
You should have a plastic trim screwed into the back of the front arches like this.
Hope that helps.
Dave
dave, thanks but its this plastic trim that im missing and i thought was a fitting kit!
Stix44 ive order the 'retainers' which were missing from my car (andy explained that they are removed when installing mud flaps) so hopefully i can get it painted and fitted soon
Hi mate, did you order the 'retainers' new then?
If so I don't supposed you have the part numbers? I'm in the same situation as you now, got the skirts but my car has mudflaps so I don't have the spacer strips.
sprinter2012
13-08-2019, 12:19 PM #29Stix44 ive order the 'retainers' which were missing from my car (andy explained that they are removed when installing mud flaps) so hopefully i can get it painted and fitted soon
Hi mate, did you order the 'retainers' new then?
If so I don't supposed you have the part numbers? I'm in the same situation as you now, got the skirts but my car has mudflaps so I don't have the spacer strips.
1 Guest(s)
1 Guest(s)
Views 1,602
Last Post by
Views 3,697
Last Post by