JapCarForum Cars, Cars, Cars! General Car Maintenance Error code- crankshaft position sensor

Error code- crankshaft position sensor

Error code- crankshaft position sensor

Pages (2): 1 2 Next
RRobert
Junior Member
Find
14
13-10-2019, 04:53 PM
#1
I did have a little search but didn't find anything, I have P0336 crankshaft sensor A circuit fault coming up via OBD. Anyone got some clue where it is, is it easy to swap the sensor yourself? Any info would be great.

Thanks..

2002 mdl.
Reply
Reply
RRobert
13-10-2019, 04:53 PM #1

I did have a little search but didn't find anything, I have P0336 crankshaft sensor A circuit fault coming up via OBD. Anyone got some clue where it is, is it easy to swap the sensor yourself? Any info would be great.

Thanks..

2002 mdl.

Reply
Reply
FirebirdPhil
Posting Freak
Find
7,101
13-10-2019, 05:34 PM
#2
Looking at the repair manual it looks very easy:
[Image: 3-DOHCEngine032.jpg]
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
Reply
Reply
FirebirdPhil
13-10-2019, 05:34 PM #2

Looking at the repair manual it looks very easy:
[Image: 3-DOHCEngine032.jpg]

"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"

Reply
Reply
RRobert
Junior Member
Find
14
13-10-2019, 05:37 PM
#3
Only on my phone and have no access to my handbook , are u meaning there will be info there or is this manual some other book I might not have. Thanks for the link, image don't look too good on phone but I'll look again later at home. Cheers.
Reply
Reply
RRobert
13-10-2019, 05:37 PM #3

Only on my phone and have no access to my handbook , are u meaning there will be info there or is this manual some other book I might not have. Thanks for the link, image don't look too good on phone but I'll look again later at home. Cheers.

Reply
Reply
FirebirdPhil
Posting Freak
Find
7,101
13-10-2019, 05:39 PM
#4
The image turned green for some reason?
Its the step by step guide from the Workshop manual, this one is 4 steps long.
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
Reply
Reply
FirebirdPhil
13-10-2019, 05:39 PM #4

The image turned green for some reason?
Its the step by step guide from the Workshop manual, this one is 4 steps long.

"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"

Reply
Reply
RRobert
Junior Member
Find
14
13-10-2019, 06:12 PM
#5
Had the error reset this evening. Went for a casual drive about 5 miles never same back on (yet). Possible bad earth/ lose wire ??
Reply
Reply
RRobert
13-10-2019, 06:12 PM #5

Had the error reset this evening. Went for a casual drive about 5 miles never same back on (yet). Possible bad earth/ lose wire ??

Reply
Reply
FirebirdPhil
Posting Freak
Find
7,101
13-10-2019, 06:37 PM
#6
Possibly, it will be a IPTA to start if it fails, at least you will know where to start looking, is it worth checking the bolt is tight enough I think they earth through the bolt???
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
Reply
Reply
FirebirdPhil
13-10-2019, 06:37 PM #6

Possibly, it will be a IPTA to start if it fails, at least you will know where to start looking, is it worth checking the bolt is tight enough I think they earth through the bolt???

"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"

Reply
Reply
Sparkystav
Administrator
Website Find
14,683
13-10-2019, 06:40 PM
#7
They earth through the bolt holding it in.

Have you had anything done in the engine recently?
[Image: LexuS-Copy.jpg]
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Reply
Reply
Sparkystav
13-10-2019, 06:40 PM #7

They earth through the bolt holding it in.

Have you had anything done in the engine recently?

[Image: LexuS-Copy.jpg]
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team

Reply
Reply
RRobert
Junior Member
Find
14
13-10-2019, 07:19 PM
#8
Had a service recently but had driven about 40 miles since the service b4 error. hope for a dodgy wire, only thing worse than an intermittent fault is a catistrophic one !!

Sump was replaced as oil plug threaded.

Thanks to all for feedback tho. :thumb:
Reply
Reply
RRobert
13-10-2019, 07:19 PM #8

Had a service recently but had driven about 40 miles since the service b4 error. hope for a dodgy wire, only thing worse than an intermittent fault is a catistrophic one !!

Sump was replaced as oil plug threaded.

Thanks to all for feedback tho. :thumb:

Reply
Reply
toxo
Posting Freak
Website Find
4,843
13-10-2019, 07:37 PM
#9
I'd be amazed if it ran properly with a broken crank position sensor, so yeah, dodgy wire would be my guess.
Reply
Reply
toxo
13-10-2019, 07:37 PM #9

I'd be amazed if it ran properly with a broken crank position sensor, so yeah, dodgy wire would be my guess.

Reply
Reply
DaveEdin
Posting Freak
Find
5,657
13-10-2019, 07:42 PM
#10
RRobert I did have a little search but didn't find anything, I have P0336 crankshaft sensor A circuit fault coming up via OBD. Anyone got some clue where it is, is it easy to swap the sensor yourself? Any info would be great.

Thanks..

2002 mdl.

Wasn't it P0335 mate? Either way, glad you have a view to sorting it...
IS200 Sport - Sold
Mazda 6 MPS - Zoom Zoom!

Modifications
Completed:
Currently 280bhp/295lbft; 3" Meercat custom exhaust; KW Suspension; FMIC; SSP; HPFP; Custom Stainless Steel Dials - for the moment, the only set in the world!! (Till the group buy for MPSOC anyway :lol: )

In Progress:
E-Tuning remap ongoing via Cobb Accessport; Braided brake lines; Stubby aerial; Tinted repeaters and sidelights; 3 Port Boost Control Solenoid; 3" HTP Intake
Reply
Reply
DaveEdin
13-10-2019, 07:42 PM #10

RRobert I did have a little search but didn't find anything, I have P0336 crankshaft sensor A circuit fault coming up via OBD. Anyone got some clue where it is, is it easy to swap the sensor yourself? Any info would be great.

Thanks..

2002 mdl.

Wasn't it P0335 mate? Either way, glad you have a view to sorting it...

IS200 Sport - Sold
Mazda 6 MPS - Zoom Zoom!

Modifications
Completed:
Currently 280bhp/295lbft; 3" Meercat custom exhaust; KW Suspension; FMIC; SSP; HPFP; Custom Stainless Steel Dials - for the moment, the only set in the world!! (Till the group buy for MPSOC anyway :lol: )

In Progress:
E-Tuning remap ongoing via Cobb Accessport; Braided brake lines; Stubby aerial; Tinted repeaters and sidelights; 3 Port Boost Control Solenoid; 3" HTP Intake

Reply
Reply
Pages (2): 1 2 Next
Recently Browsing
 1 Guest(s)
Recently Browsing
 1 Guest(s)
Related Threads…
'04 Lexus SC430 Oxygen sensor replacement
by cth
Replies 15
Views 2,079
28-04-2020, 08:42 AM
Last Post by toxo